Blar i Studentoppgaver (TN-IKM / TN-IMBM) på tittel
Viser treff 512-531 av 1213
-
Finite element analyse av en skråstagsbro
(Bachelor thesis, 2023)This thesis provides a static analysis of a Cable-Stayed Bridge using the Finite Element Analysis in ANSYS Workbench software. The static loads that were taken into consideration are the traffic loads and the static wind ... -
Finite element analysis and experimental testing of lifting capacity for GRP cover.
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013)Structures made of glass reinforced plastic (GRP), often abbreviated GRP cover, are used to protect subsea equipment in the oil and gas industry. These structures need to be lifted during fabrication, transportation and ... -
Finite Element Analysis and Fatigue Damage Assessment of a Railway Bridge Subjected to Variable Amplitude Loading
(Bachelor thesis, 2023)Many of the railway bridges in Norway and the rest of the world are closing in on the end of their predicted service life, and the need for more precise fatigue life assessments and predictions is challenging for the railway ... -
Finite element analysis of a friction clamp located on a North Sea jacket
(Masteroppgave/UIS-TN-IKM/2011;, Master thesis, 2011)This master thesis is written on the University of Stavanger spring 2011 in collaboration with Subsea 7. When transporting hydrocarbons from seabed to top side on a jacket platform there is always the need of a riser. ... -
Finite Element Modelling and Analysis of Axial Settlement of Light Poles
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020)The slip joint technology is a method for connecting two conical pole segments together, without the use of bolts or grout, thus reducing time of installation and the need of maintenance. In recent years there have been ... -
Finite Element Models for Integrity Assessment of Flexible Riser with Damaged Tensile Wires
(Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06)Many of the flexible risers in service do not meet their documented service life. A common failure mode is the rupture of the abrasive external layer which, in itself, is not critical, but seawater ingress may corrode ... -
FishTrapSafe: Fra ide til ferdig produkt
(Bachelor thesis, 2022)During fishing activities, it is not uncommon that some of the equipment gets lost because of bad weather or bad luck during operations. However, an increasing problem faced by fishers is the loss of gear because of theft. ... -
Flatdekke kaikonstruksjon med eller uten spennarmering
(Masteroppgave/UIS-TN-IKM/2011;, Master thesis, 2011)Denne oppgåva omhandlar bruk av flatdekke som dekke-element i kaikonstruksjonar. Målet med oppgåva er å konstruere eit vekt-, tids-, og kostnadseffektivt alternativ til dagens kaidekkeelement. For å synleggjere eventuelle ... -
Flatdekke med spennarmering
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013)Denne rapporten omhandler et flatdekke med spennarmering. Det aktuelle dekket er en del av en konstruksjon som er under utbygging i Sandnes. Dette stedstøpte og etterspente dekket skal brukes som parkeringsareal. Rapporten ... -
Flexible riser global analysis for very shallow water
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013)Flexible risers are widely used for a range of water depths and can accommodate large floater motions when using a buoyant system. A wide range of buoyancy solutions have been developed for very shallow water (e.g. 30-50 ... -
Flexural behavior of cracked reinforced concrete beams with externally bonded CFRP plates
(Master thesis, 2021)The purpose of this thesis is to perform an experimental study of the flexural behavior of damaged reinforced concrete beams strengthened with externally bonded Carbon Fiber Reinforced Polymer (CFRP) plates. Damage have ... -
Floating wind turbines : the transport phase
(Masteroppgave/UIS-TN-IKM/2009, Master thesis, 2008)The worldwide demand of renewable energy is increasing rapidly because of the climate problem. Wind energy appears as a clean and good solution to cope with a great part of this energy demand. Therefore, floating wind ... -
Flow Introduced Turbulence & Pulsation Assessment for Subsea Spools
(Master thesis, 2021) -
Flow Simulation to Study SMART KITE Design
(Master thesis, 2021)The Potsdam Propeller Test Case PPTC propeller was used as the turbine for the flow simulation of the tethered undersea kite TUSK energy system in this project. OpenFOAM ‘propeller’ and ‘wingmotion’ tutorials used as ... -
Flytebro forankret på store dyp
(Masteroppgave/UIS-TN-IKM/2012;, Master thesis, 2012)Det er store utfordringer knyttet til fjordkrysninger når vanndybden blir for stor for bunnfaste fundamenter og fjorden for bred for konvensjonelle broer. Denne oppgaven omhandler spesielt krysning av Boknafjorden som er ... -
Forces on simplified offshore structures according to different wave models.
(Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)The reason for creating this thesis was because of the new and revised version of NORSOK N-003 standard. Therefore a comparison between the old and the revised version of NORSOK N-003 standard has been performed. This ... -
Forsknings –og utdanningsinfrastruktur i offentlig organisasjon – en case studie hos Det teknisk-naturvitenskaplige fakultet ved Universitet i Stavanger.
(Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)Den offentlige sektoren er stadig under et mer krevende regime, hvor både ressurser og økonomi fremstår som begrensende faktorer. Dette medfører at økt effektiv styring og produktivitet er nøkkelfaktorer for å oppnå bedre ... -
Forslag om bruk av Dynamo for en effektiv arbeidsflyt mellom Revit og FEM-Design
(Master thesis, 2022)Byggebransjen er under en enorm teknologisk utvikling som åpner opp for nye metoder som bidrar til en mer effektiv prosjektering. Her er parametrisk design et fremadstormende verktøy som benyttes til dette formålet. Denne ... -
Framework for Effective Spare Parts Management in Late-Life/End-Life From Planning to Decommissioning & Removal
(Master thesis, 2021)The Norwegian oil and gas industry is at an earlier stage of maturity. As the end of the lifecycle for an offshore asset is approaching, decommissioning activities must be initiated. The decommissioning process is the final ... -
Free Hanging Catenary Riser with Steel and Titanium
(Master thesis, 2022)Deepwater developments are becoming increasingly common in several parts of the world. Although the technological advances have grown exponentially since the first development in such great depth, challenges are still faced ...