Blar i Department of Mechanical and Structural Engineering and Materials Science (TN-IMBM) på tittel
Viser treff 1109-1128 av 1695
-
Numerical modeling of recycled fibre reinforced concrete beams and comparison with experimental findings
(Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06)The presented work has the main focus on fibre reinforced concrete (FRC). FRC is examined in ATENA, and the numerical results are compared to the experimental. The first part of this report treats the concept of nonlinear ... -
Numerical modeling of Reinforced Concrete Squat Shearwalls using FRP
(Master thesis, 2023)Reinforced concrete shear walls are the most common resistance system against lateral loads in reinforced concrete structures. Despite this, many of the reinforced concrete shear walls in the world need to be strengthened ... -
Numerical Modelling and Global Response Assessment of Floating Docks towards Efficient, Safer and Autonomous Docking Operations
(PhD thesis UiS;, Doctoral thesis, 2024)Floating docks are known for their construction efficiency and operational flexibility compared to traditional graving docks. They play an important role in shipyards by serving as essential platforms for vessel construction, ... -
Numerical modelling of hydrodynamic responses of Ocean Farm 1 in waves and current and validation against model test measurements
(Peer reviewed; Journal article, 2021)With the continuous growing of the aquaculture industry and increasingly limited fish farming sites at close to shore areas both in Norway and worldwide, there is a need to develop fish farms suitable for aquaculture ... -
Numerical Optimisation of a Classical Stochastic System for Targeted Energy Transfer
(Peer reviewed; Journal article, 2022)The paper studies stochastic dynamics of a two-degree-of-freedom system, where a primary linear system is connected to a nonlinear energy sink with cubic stiffness nonlinearity and viscous damping. While the primary mass ... -
Numerical Simulation and Customized DACM Based Design Optimization
(PhD thesis UiS;, Doctoral thesis, 2018)The diverse numerical modelling, analysis and simulation tools that have been developed and introduced to markets are intended to perform the virtual design and testing of products and systems without the construction of ... -
Numerical Simulation of Breaking Wave Loading on Standing Circular Cylinders with Different Transverse Inclined Angles
(Peer reviewed; Journal article, 2020)The purpose of this paper is to numerically simulate the breaking wave past a standing cylinder with different transverse inclined angles. The numerical simulations are carried out by solving the Unsteady Reynolds-Averaged ... -
Numerical simulation of FDM manufactured parts by adopting approaches in composite material simulation
(Peer reviewed; Journal article, 2019-11)Additive manufacturing (AM) process is a promising manufacturing method that can replace conventional manufacturing methods, particularly for parts with complex geometry. It is the process of joining materials layer by ... -
Numerical Simulation of Flow Around Subsea Covers at high Reynolds Numbers
(Masteroppgave/UIS-TN-IMBM/2019;, Master thesis, 2019-06-15)The present study investigates turbulent flow over square and trapezoidal wall-mounted subsea covers in single and tandem configuration. The structures under investigation in the single configuration are subjected to a ... -
Numerical Simulation of Flow around Subsea Covers at High Reynolds Numbers
(Masteroppgave/UIS-TN-IKBM/2019;, Master thesis, 2020-01-15)Glass Reinforced Plastic (GRP) covers are widely used to protect the subsea equipment from external damage. In this work, numerical simulations of a fully developed turbulent boundary layer flow over square and trapezoidal ... -
Numerical simulation of flow around two 5:1 rectangular cylinders at a high Reynolds Number
(Peer reviewed; Journal article, 2019)The unsteady flows around two stationary rectangular cylinders with a chord-to-thickness ratio of B/D = 5 at ReD = 2 × 105 (based on the free stream velocity and the width length D), are investigated using two-dimensional ... -
Numerical simulation of ice sheet – FPSO interaction
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013-06)The present thesis is devoted to investigation of FPSO interaction with level ice. The interaction with level ice is only addressed, disregarding other ice features. The scope of the thesis focuses upon two major problems: ... -
Numerical Simulation of Industrial Ultrasonic Testing of Material
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-06-29)In this thesis, numerical simulation of ultrasonic testing is developed by modeling three different materials including Perspex, water, and steel in each model. Procedures of calibration of An angle probe including timebase ... -
Numerical simulation of oxygen transport in land-based aquaculture tank
(Peer reviewed; Journal article, 2021-10)Dissolved oxygen is an important indicator of the water quality and important for fish survival in aquaculture. The distribution of the dissolved oxygen is highly dependent on the flow motions, the pressure and the temperature ... -
Numerical simulation of piggyback pipelaying under current loadings
(Peer reviewed; Journal article, 2023)For piggyback pipelaying operations, current-induced force and its effect on the piggyback pipe have not been thoroughly studied. In the present study, an improved method in hydrodynamic load calculation and structural ... -
Numerical Simulation of VIV of Risers with Staggered Buoyancy Elements
(Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06-15)Steel Lazy Wave Riser (SLWR) is an attractive deep water riser system design, which allows the platform motion to be decoupled from the touchdown point (TDP) of the riser. When subjected to external flow, both buoyancy ... -
Numerical simulation-based effect characterization and design Optimization of micro cross-flow turbine
(Peer reviewed; Journal article, 2019)In this era of high power demand along with a need for sustainability, small and micro-scale hydro turbines are indispensable, especially for off-grid power generation. These hydro-turbines are more appealing, particularly ... -
Numerical simulations of flow around two tandem wall-mounted structures at high Reynolds numbers
(Peer reviewed; Journal article, 2020)In the present study, the flow around two-dimensional (2D) square and trapezoidal wall- mounted structures in tandem on a horizontal flat wall has been simulated using two-dimensional Reynolds-averaged Navier-Stokes (RANS) ... -
Numerical Simulations of Flow Over Bottom-Mounted Structures at High Reynolds Number
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2019-06)A common challenge in on-bottom stability design is to select accurate hydrodynamic quantities, such as drag and lift coefficients, to compute the forces on structures subject to fluid flow. The objective of the present ... -
Numerical simulations of flow-induced vibrations of two rigidly coupled cylinders with uneven diameters in the upper transition Reynolds number regime
(Peer reviewed; Journal article, 2021)Two degree-of-freedom (2-DoF) flow-induced vibrations (FIV) of two rigidly coupled cylinders are numerically investigated at the Reynolds number of 3.6 × 106. Two- dimensional (2D) Unsteady Reynolds-Averaged Navier–Stokes ...