Blar i Department of Mechanical and Structural Engineering and Materials Science (TN-IMBM) på tittel
Viser treff 1347-1366 av 1691
-
Risk-based work optimization for deep water drilling operations: Integration of risk analysis, maintenance and human factors on BOP operation
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013-10-10)The offshore deep water drilling has attracted global attention since the Macando blowout. It raised worldwide concern on the safety level of oil & gas industry and resulted in directly influence on offshore drilling ... -
Road Transportation Challenges in the Arctic
(Peer reviewed; Journal article, 2020)Despite all efforts to mitigate global warming, its rate and magnitude are still rising where transportation is considered to be an important contributor. In the Arctic regions however, unstable weather conditions, strong ... -
Roadmap for upscaling operational capacity
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-06-14)It has been evident to the market that there is a desperate need for environmental-friendly industrial heat pumps that could deliver heat above 150ºC, as this is the highest temperature today's heat pumps can deliver. This ... -
Rotasjonsstivhet av sveiste T-knutepunkter, sammensatt av kvadratiske hulprofiler utsatt for i-planet bøyning
(Masteroppgave/UIS-TN-IKM/2011;, Master thesis, 2011)Kvadratiske og rektangulære hulprofiler er benyttet i et bredt spekter rammer og fagverk, både i landbasert byggevirksomhet og offshoreindustrien. Sammenføyningen forekommer ofte ved at gurt og stav er sammensveist normalt ... -
S-N curve for riveted details in corrosive environment and its application to a bridge
(Peer reviewed; Journal article, 2020-01)A formula for stress‐life curve is proposed to predict the fatigue life of riveted bridges located in corrosive environments. The corrosive environment‐dependent parameters of the S‐N curve are determined based on the ... -
Safety and Emergency Response Associated with Cold Climate Marine Operations
(PhD thesis UiS;, Doctoral thesis, 2020)This dissertation is developed by GMC Maritime and the University of Stavanger and is part of the industrial PhD program at the Norwegian Research Council. The aim of the work is to identify the governing mechanisms ... -
Safety related study of Expanding Pin systems application in lifting and drilling equipment within Construction, Offshore, and Marine sectors
(Peer reviewed; Journal article, 2021)A questionnaire-based survey has been performed among original equipment manufacturers (OEMs), sub-suppliers, engineering companies, end-users, service & maintenance, and “others”, as part of an investigation to clarify ... -
Sammenligning av måledata fra Lysefjordbrua med en eksisterende FE-modell
(Masteroppgave/UIS-TN-IKM/2014;, Master thesis, 2014-06-16)Denne oppgaven omhandler en analyse av vindrespons av Lysefjordbrua. Brua har et hovedspenn på 446 m som krysser Lysefjorden i Forsand kommune. Universitetet i Stavanger (UiS) har i samarbeid med blant annet Statens ... -
Sammenligningsstudie mellom CLT-Glulam og betong-kamstål. Et dypdykk i tilgjengelig LCA-data for å fastslå klimautslippsforskjeller.
(Bachelor thesis, 2023)I Norge bruker vi både betong og treverk når vi bygger. Det kan virke som enhver bygning er sammensatt av enten den ene, eller den andre. Begge disse materialene har vist seg å være praktiske byggematerialer, det er ikke ... -
Sammenlikning av knutepunktsgeometri på en offshore fiskefarm
(Bachelor thesis, 2023)This thesis was written in collaboration with Global Maritime (GM), and its aim is to compare two geometrically different structural joints on an offshore fish farm, named GM Aqua Design. The two models are compared on ... -
Samvirke mellom yttersjikt og innersjikt i sandwichelement med ikkje-metalliske sjiktforbinderar
(Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06-23)I denne oppgåva er det testa ut ståande slanke veggelement armert med basaltfiber i yttersjiktet. Betongsjikta er forbundne med ein type sjiktforbinderar av glasfiber som hittil har vore i lite bruk i Noreg, men som i stor ... -
Scalability and compatibility analyses of airborne wind technology for maritime transport
(Peer reviewed; Journal article, 2019)Wind energy is a source freely available in the oceans. New developments in the wind industry are towards high altitude wind turbines, known as Airborne Wind Energy Systems. The airborne wind technology is rapidly developing ... -
Scalability and Compatibility Assessment of Airborne Wind Technology in Maritime Transport: a case of electricity generation on a vessel
(Masteroppgave/UIS-TN-IMBM/2019;, Master thesis, 2019-06-12)The Maritime industry is facing a challenge in reducing its dependency on fossil fuels. New regulations established to reduce the GHG emissions by maritime transport, force sector stakeholders to apply measurements and ... -
Scale operations from monohull vessel
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013)The advances within the oil and gas industry have provided opportunities to expand into deeper and more remote areas. One of the most important technological advances comes from the development of subsea equipment. The ... -
SCFs Calculation and fatigue life determination of tubular joints
(Bachelor thesis, 2021)This thesis covered the subject of design optimization of tubular joints, with a focus on joints with loaded chord members. This type of loading can have an effect on the overall fatigue performance of the joints and by ... -
Seawater hydraulic pump unit
(Bachelor thesis, 2022)Summary This thesis is part of a concept development for a seawater hydraulics pump unit, intended for a new generation of Subsea Remote Operated Vehicles ROVs in development by Oceaneering. This includes evaluating the ... -
Seismic Assessment of Offshore Monopile Foundation With Variable Magnitude Moments
(Master thesis, 2022)The recent advances in offshore technology has led to deeper exploratory excursions, easier structure installation and monitoring as well as remotely-monitored maintenance work , which has been a primer for increase in ... -
Seismic performance assessment of reinforce concrete: a case study of Kanti Children's Hospital, Kathmandu, Nepal
(Masteroppgave/UIS-TN-IMBM/2018;, Master thesis, 2018-06)Structures should be ensured good structural performance in the event of high magnitude earthquakes. This thesis is built around a case study of Kanti Children’s Hospital, Kathmandu, Nepal where there is a history of high ... -
Seismic response of floating bridges
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-06-15)The object of this study is to collect the results of an end-anchored floating bridge when it is subjected to seismic excitations. The bridge is an end-anchored floating bridge, mounted on 46 separate pontoons, with an ... -
Selection of Corrosion Monitoring Equipment for Subsea Safety Joint
(Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06-15)In Nature, most of all Metals evolve as stable ores of chemical compounds like oxides, sulphides or carbonates. Lot of energy is required to refine and make them useful for some means for every Industry. Corrosion on ...