Blar i Department of Mechanical and Structural Engineering and Materials Science (TN-IMBM) på tittel
Viser treff 1459-1478 av 1695
-
Studies of Post-Fabrication Heat Treatment of L-PBF-Inconel 718: Effects of Hold Time on Microstructure, Annealing Twins, and Hardness
(Peer reviewed; Journal article, 2021-02)The widely adopted temperature for solid solution heat treatment (ST) for the conventionally fabricated Inconel 718 is 1100 °C for a hold time of 1 h or less. This ST scheme is, however, not enough to dissolve Laves and ... -
Studies on the Geometrical Design of Spider Webs for Reinforced Composite Structures
(Peer reviewed; Journal article, 2021-02)Spider silk is an astonishingly tough biomaterial that consists almost entirely of large proteins. Studying the secrets behind the high strength nature of spider webs is very challenging due to their miniature size. In ... -
Study of Acergy`s supplier database
(Masteroppgave/UIS-TN-IKM/2009;, Master thesis, 2011)Acergy Norway AS is a seabed-to-surface engineering and construction company for the offshore oil and gas industry worldwide. They deliver services in many market segments such as Inspection and Maintenance and Repair ... -
Study of Bondura® Expanding PIN System – Combined Axial and Radial Locking System
(Peer reviewed; Journal article, 2021)Bolted connections are widely used in parallel plates and flanged joints to axially lock using the preload generated by the tightening torque and to constrain radial movements of the flanges by the surface friction between ... -
Study of DataOps as a concept for Aker BP to enable data-driven assets.
(Master thesis, 2022)The oil and gas industry have faced many obstacles over the decades and in recent years the industry has had to endure increased pressure from the market, a global crisis caused by the coronavirus and oil prices reaching ... -
Study of dynamic response of a suspension bridge in relation to recorded traffic-induced acceleration
(Master thesis, 2023)This master's thesis is the final work of my master’s degree in structural and material science at the University of Stavanger and marks the ending of 5 consecutive years studying engineering. This thesis aims to investigate ... -
Study of lifting operation of a tripod foundation for offshore wind turbine
(Master thesis, 2017-06)Marine lifting operations play a key role in the installation of turbines and bottom-fixed foundations. Offshroe installations of the bottom-fixed foundations, tripod foundation in this study, are costly and risky due to ... -
Study of Machinability in Drilling Operation of Enset–Sisal Hybrid Polyester Composite
(Journal article; Peer reviewed, 2022-07-14)Due to their light weight, low density, high-specificity strength, and ease of fiber surface treatment, natural-fiber-reinforced composites are recognized as the most suitable materials for interior part applications. ... -
Study of medical image data transformation techniques and compatibility analysis for 3D printing
(Master thesis, 2022)Various applications exist for additive manufacturing (AM) and reverse engineering (RE) within the medical sector. One of the significant challenges identified in the literature is the accuracy of 3D printed medical ... -
Study of production tolerances' effect on capacities with regards to EN-1999
(Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06-14)The goal of this thesis was to investigate the effect that production tolerances has on the strength capacities of a beam or column. The out-of-straightness imperfection on a pinned column, and its effect on the flexural ... -
Study of rail-wheel contact problem by analytical and numerical approaches
(Peer reviewed; Journal article, 2021)This study presents the rail wheel contact problems under normal and tangential categories. Both analytical and numerical approaches were used for modelling, where the analytical approach assumed elliptical contact patches ... -
Study of the Characteristics of Acoustic Emission Signals.
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-07-15)This report aims to study the characteristics of signals collected by Acoustic Emission Testing (AET) and categorize them into types to detect yield. A literature survey of existing knowledge of AET and Acoustic Emission ... -
Study of the Characteristics of AET Signals for Structural Health Monitoring
(Master thesis, 2021)This research aims to study the characteristics of acoustic emission signals emitted from a steel sample under loading. The thesis is a continuation of previous theses submitted in 2019 by Dawood and in 2020 by Nguyen. ... -
Study of the Effects of Alkali Treatment and Fiber Orientation on Mechanical Properties of Enset/Sisal Polymer Hybrid Composite
(Peer reviewed; Journal article, 2023-01)Abstract In the manufacturing process of innovative fiber-based composite materials, natural fibers are among the most commonly employed reinforcements. In this study, Enset/Sisal (E/S) fiber with a polyester matrix was ... -
Study of the module handling system on Seven Viking
(Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)Subsea installations is a vital part of the oil and gas industry, but as have also been a major cost factor. When the oil price decline, subsea installations are one of the first fields to be affected. The priority to cost ... -
Study of the Performance of Natural Fiber Reinforced Composites for Wind Turbine Blade Applications
(Peer reviewed; Journal article, 2020)Availability of some form of energy is essential for human survival and social development. However, the way energy has been generated within the last century has brought forward the quest for generation of energy without ... -
Study of vessel performance in extreme loading conditions for a new built offshore construction vessel during installation of flexible flowline
(Masteroppgave/UIS-TN-IKM/2014;, Master thesis, 2014-06-16)A new built vessel need to carry out extensive sea trials before being put in what could be considered as “normal operation”. This is done to make sure the capabilities of the vessel are known to the vessel’s crew, captain, ... -
Study of weld design and cost versus fabrication cost
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013)Increasing demand in economic- and time-efficiency, in the production and design phase, has led to the question if there is a possibility to save time and money on a more detailed analysis on which weld type to use. The ... -
Study on Development Strategies of a Small and Medium-sized Enterprise in Dynamic Environment
(Masteroppgave/UIS-TN-IMBM/2018;, Master thesis, 2018-03)The role of SMEs in promoting economic prosperity and solving employment has become increasingly evident. In the large-scale trade of industrial products, SMEs can also play their unique role and form a new impetus for ... -
Study on Digitalization in Industry: Requirements and Assessment
(Masteroppgave/UIS-TN-IMBM/2018;, Master thesis, 2018-06)Digitalization is a way of companies preparing for the future. Most large established enterprises embark on the digitalization process without a sense of direction. This research will provide a way forward for the ...