Blar i Department of Mechanical and Structural Engineering and Materials Science (TN-IMBM) på tittel
Viser treff 718-737 av 1730
-
Finite element method-based modeling of bending under tension friction test of deep drawing quality steel sheets
(Peer reviewed; Journal article, 2019)Understanding of the effect of the friction on the sheet deformation is a key factor in design and realization of stamping process. Among others, bending under tension friction test simulates the frictional phenomena on ... -
Finite Element Modelling and Analysis of Axial Settlement of Light Poles
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020)The slip joint technology is a method for connecting two conical pole segments together, without the use of bolts or grout, thus reducing time of installation and the need of maintenance. In recent years there have been ... -
Finite Element Models for Integrity Assessment of Flexible Riser with Damaged Tensile Wires
(Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06)Many of the flexible risers in service do not meet their documented service life. A common failure mode is the rupture of the abrasive external layer which, in itself, is not critical, but seawater ingress may corrode ... -
FishTrapSafe: Fra ide til ferdig produkt
(Bachelor thesis, 2022)During fishing activities, it is not uncommon that some of the equipment gets lost because of bad weather or bad luck during operations. However, an increasing problem faced by fishers is the loss of gear because of theft. ... -
Flatdekke kaikonstruksjon med eller uten spennarmering
(Masteroppgave/UIS-TN-IKM/2011;, Master thesis, 2011)Denne oppgåva omhandlar bruk av flatdekke som dekke-element i kaikonstruksjonar. Målet med oppgåva er å konstruere eit vekt-, tids-, og kostnadseffektivt alternativ til dagens kaidekkeelement. For å synleggjere eventuelle ... -
Flatdekke med spennarmering
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013)Denne rapporten omhandler et flatdekke med spennarmering. Det aktuelle dekket er en del av en konstruksjon som er under utbygging i Sandnes. Dette stedstøpte og etterspente dekket skal brukes som parkeringsareal. Rapporten ... -
Flexible riser global analysis for very shallow water
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013)Flexible risers are widely used for a range of water depths and can accommodate large floater motions when using a buoyant system. A wide range of buoyancy solutions have been developed for very shallow water (e.g. 30-50 ... -
Flexural behavior of cracked reinforced concrete beams with externally bonded CFRP plates
(Master thesis, 2021)The purpose of this thesis is to perform an experimental study of the flexural behavior of damaged reinforced concrete beams strengthened with externally bonded Carbon Fiber Reinforced Polymer (CFRP) plates. Damage have ... -
Flexural dynamic behavior of submerged cylindrical structures under wave loads
(Peer reviewed; Journal article, 2019-11)Abstract. An analytical solution for the dynamic response of submerged slender circular cylindrical structure subjected to linear wave loads is presented. A double Laplace transform with respect to temporal and spatial ... -
Flexural dynamic response of monopile foundations under linear wave loads
(Peer reviewed; Journal article, 2020-03)An analytical solution for the dynamic response of submerged slender circular cylindrical structures subjected to linear wave loads is presented. A double Laplace transform with respect to temporal and spatial variables ... -
Floating wind turbines : the transport phase
(Masteroppgave/UIS-TN-IKM/2009, Master thesis, 2008)The worldwide demand of renewable energy is increasing rapidly because of the climate problem. Wind energy appears as a clean and good solution to cope with a great part of this energy demand. Therefore, floating wind ... -
Floating wind turbines structural details fatigue life assessment
(Peer reviewed; Journal article, 2023)Fatigue damage prediction is essential for safety of contemporary offshore energy industrial projects, like offshore wind turbines, that are to be designed for sufficiently long operational period of time, with minimal ... -
Flow around two elastically-mounted cylinders with different diameters in tandem and staggered configurations in the subcritical Reynolds number regime
(Peer reviewed; Journal article, 2021)Flow around two cylinders with different diameters undergoing Flow-Induced Vibrations (FIV) in the subcritical flow regime is investigated using two-dimensional Unsteady Reynolds Averaged Navier-Stokes (URANS) approach. ... -
Flow Introduced Turbulence & Pulsation Assessment for Subsea Spools
(Master thesis, 2021) -
Flow over a step cylinder using partially-averaged Navier-Stokes equations with application towards dynamic subsea power cables
(Peer reviewed; Journal article, 2023)Understanding the flow characteristics of buoyancy sections in power cable and umbilical configurations is crucial for analyzing floating offshore wind turbine systems. Buoyancy sections decouple the motions from the floater ... -
Flow Simulation to Study SMART KITE Design
(Master thesis, 2021)The Potsdam Propeller Test Case PPTC propeller was used as the turbine for the flow simulation of the tethered undersea kite TUSK energy system in this project. OpenFOAM ‘propeller’ and ‘wingmotion’ tutorials used as ... -
Flytebro forankret på store dyp
(Masteroppgave/UIS-TN-IKM/2012;, Master thesis, 2012)Det er store utfordringer knyttet til fjordkrysninger når vanndybden blir for stor for bunnfaste fundamenter og fjorden for bred for konvensjonelle broer. Denne oppgaven omhandler spesielt krysning av Boknafjorden som er ... -
Forces on simplified offshore structures according to different wave models.
(Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)The reason for creating this thesis was because of the new and revised version of NORSOK N-003 standard. Therefore a comparison between the old and the revised version of NORSOK N-003 standard has been performed. This ... -
Forsknings –og utdanningsinfrastruktur i offentlig organisasjon – en case studie hos Det teknisk-naturvitenskaplige fakultet ved Universitet i Stavanger.
(Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)Den offentlige sektoren er stadig under et mer krevende regime, hvor både ressurser og økonomi fremstår som begrensende faktorer. Dette medfører at økt effektiv styring og produktivitet er nøkkelfaktorer for å oppnå bedre ... -
Forslag om bruk av Dynamo for en effektiv arbeidsflyt mellom Revit og FEM-Design
(Master thesis, 2022)Byggebransjen er under en enorm teknologisk utvikling som åpner opp for nye metoder som bidrar til en mer effektiv prosjektering. Her er parametrisk design et fremadstormende verktøy som benyttes til dette formålet. Denne ...