Browsing Studentoppgaver (TN-IKM / TN-IMBM) by Subject "maskinkonstruksjon"

Now showing items 21-30 of 30

    • Optimization of 2K-mixer for Paint 

      Khalid, Adnan (Masteroppgave/UIS-TN-IMBM/2019;, Master thesis, 2019-06-15)
      This work presents a parametric study of a 2K-mixer for paint application that utilizes static mixers for mixing two component paint applied on a car body. The mixers is installed in a specialized valve block giving it the ...

    • Optimization of Guide Structure for Elevators on Ships 

      Øie, Geir Marius (Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06-15)
      The existing design of marine and offshore elevators are mainly based on the expertise out of land-based elevators, with higher safety factors and all existing requirements being fulfilled. In the design of the guide ...

    • Optimization of Multirotor UAV Endurance 

      Sem, Sølve Sætre (Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020)
      Advancements in the technology of electric motors, batteries and control modules have facilitated a steep increase in the interest of small battery-powered multirotor aircraft. Unmanned areal vehicles (UAV) of this type ...

    • Preliminary Concept Study: Selection of Optimal Lightweight Design Concept for Offshore Platform P&A 

      Ippolito, Gabriel Mikal (Masteroppgave/UIS-TN-IMBM/2019;, Master thesis, 2019-06-15)
      As more facilities are nearing the end of their design life on the Norwegian Continental Shelf (NCS), the volume of costly plug and abandonment (P&A) operations is on the rise. Current practice is to use expensive drilling ...

    • Preliminary design of a fuel cell - battery hybrid propulsion system for a small VTOL UAV 

      Brun, Ninni Sofie (Masteroppgave/UIS-TN-IMBM/2018;, Master thesis, 2018-06-14)
      Over the past decade, utilization of unmanned aerial vehicles (UAVs) in military and commercial applications has increased significantly. The vertical take-off and landing (VTOL) UAV is appreciated for its easy launch and ...

    • Sprekkvekst og inspeksjonsplanlegging 

      Neraas, Håkon (Masteroppgave/UIS-TN-IMBM/2019;, Master thesis, 2019)
      Hensikten med denne oppgaven er å undersøke behovet for inspeksjoner for å oppdage sprekkvekst i et kritisk knutepunkt på en offshore jacket underlagt syklisk bølgebelastning. Det er studert hvor ofte det er nødvendig med ...

    • Stress analysis of simple tubular joints - Loaded chord members 

      Sagir, Abdullahi (Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-06-29)
      This thesis covered the subject of stress analysis in simple tubular joints, with a focus on tubular joints with loaded chord members. The type of loading investigated is even though quite common, not very much investigated. ...

    • Structural Response Analysis of a Composite Multirotor Airframe 

      Fischer, Joakim (Masteroppgave/UIS-TN-IMBM/2019;, Master thesis, 2019-06-15)
      In this work, finite element analyses determine the modal frequencies and relative stiffness of two multirotor airframes---the Camflight FX-8 and its water-resistant variant BG-200. Details of the analysis ...

    • Water Hammer Induced Vibration of Steel Pipelines Repaired with FRP Composites 

      Rege, Kristen (Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06-14)
      Since the 1990s, there has been an increasing trend to repair corroded or eroded pipelines, conveying oil, gas or water, by using fibre-reinforced polymer (FRP) composites. This relatively new repair technique involves ...

    • Wind Flow Simulation over Fish Farm Feed Barge 

      Nuland, Svein Erik (Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06-15)
      There are approximate over 1000 fish farms in Norway, where half are connected to the grid and the rest are driven by diesel generators. Fish farms use large air compressors to feed the fish, which creates high power ...