Browsing Department of Mechanical and Structural Engineering and Materials Science (TN-IMBM) by Title
Now showing items 955-974 of 1695
-
Management of challenges during the construction of offshore facilities
(Peer reviewed; Journal article, 2019)The construction of offshore facilities for development of oil and gas deposits is preceded by careful Conceptual Studies, Front-End Engineering Design Studies (FEED studies) and a Detailed Engineering phase including ... -
Managing hidden system threats for higher production regularity using intelligent technological solutions: A case study
(Journal article; Peer reviewed, 2010)Identification and interpretation of hidden system threats on complex oil and gas production platforms has always been a challenge. These threats may gradually develop into failures/faults resulting in system shutdowns or ... -
Managing the efficiency of foreign engineering contracts: A study of a Norwegian and South Korean project interface
(Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)Oil & gas exploration and production industry in North Sea has greatly been challenged over the last decade with increasing cost profiles. This condition, together with relatively low oil price has begun to squeeze the ... -
Mapping the potentials of regions in Europe to contribute to new knowledge production in Industry 4.0 technologies
(Peer reviewed; Journal article, 2021-04)This paper aims to identify the future Industry 4.0 technology (I4T) centres of knowledge production in Europe. We expect I4Ts to thrive in regions where they can draw on local capabilities in I4T-related technologies. We ... -
Marine Operations in Arctic conditions
(Peer reviewed; Journal article, 2023)Marine operations require careful early planning and thereafter detailed planning prior to project execution. The time from initiating an operation to finalization of the activity is typically several days. The activity ... -
Market-analysis of software for predictive maintenance solutions inthe Norwegian petroleum industry
(Master thesis, 2021)The Norwegian petroleum industry is currently undergoing a drastic technological change, often termed Industry 4.0. With this change, new innovative capabilities emerge across all operations and disciplines. Predictive ... -
Material characteristics of 3-D printed steel
(Master thesis, 2021)Additive manufacturing of metals is a technology where metal parts are built layer by layer from a 3D model. To do this a heat source is used to melt metal powder or metal rods. There is a large selection of processes that ... -
Material degradation in mooring chains for floating structures in deep waters
(Master thesis, 2022)There is a dire need for an efficient, trustworthy, and financially feasible positioning technique for offshore large floating structures. Of all the methods of positioning the offshore structures, the mooring chains play ... -
Material usage of offshore wind turbines, and its sustainability impact on the environment.
(Master thesis, 2022)As the world is working towards a greener energy environment, we see that more and more companies are changing their course to meet the green shift. Our future jobs will try to move more away from oil and fossil fuels, and ... -
Materialkvalitet til INCONEL 718 additivt tilvirket av skrapmetallbasert pulver
(Bachelor thesis, 2024)Additive tilvirkningsteknikker er mer og mer aktuelt som produksjonsmetode. Dette gjør at man raskt kan produsere prototyper eller nye deler, bygge på eller reparere eksisterende deler. Det grønne skiftet er her, og F3Nice ... -
Måling av arbeidsprosesser for Ferdigstillelsesgruppen i Reinertsen AS
(Masteroppgave/UIS-TN-IKM/2011;, Master thesis, 2011)Oppgaven har som mål å etablere metoder for å måle arbeidsprosessene som inngår i gjennomføringen av mekanisk ferdigstillelse, systemutprøving og overlevering. For å kunne gjøre dette har det vært nødvendig for forfatter ... -
MBSE to support Asset Maintenance & Integrity: Requirement and Behavioral analysis
(Master thesis, 2022)The oil and gas industry has been an important contributor to Norway’s economy ever since oil and gas production started on the Norwegian continental shelf. The oil and gas industry needs innovative solutions to stay ... -
Measurements of Surface-Layer Turbulence in a Wide Norwegian Fjord Using Synchronized Long-Range Doppler Wind Lidars
(Peer reviewed; Journal article, 2017)Three synchronized pulsed Doppler wind lidars were deployed from May 2016 to June 2016 on the shores of a wide Norwegian fjord called Bjørnafjord to study the wind characteristics at the proposed location of a planned ... -
Mechanical and microstructual investigation of 3D-printed Alloy 625
(Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06)Additive manufacturing is in the wind and shows great promise as a manufacturing technique. In this thesis the properties of the additive manufactured EOS alloy 625 is investigated. Tensile, CharpyV, Vickers, and pitting ... -
Mechanical and microstructural analysis of 3D-Printed 316L stainless steel
(Master thesis, 2021)The project aims to analyze the mechanical properties and microstructure study of 316L stainless steel, which is as-printed using the selective laser melting (SLM) technique. Metal components produced by the SLM process ... -
Mechanical and microstructural assessment of a novel 3D-printed AlSi10Mg- Ti6Al4V alloy using Direct Laser Deposition
(Master thesis, 2023)A novel AlSi10Mg-Ti6Al4V alloy fabricated through DLD was investigated. The novel alloy consists of 92 wt.% AlSi10Mg and 8 wt.% Ti6Al4V. The alloy was found to have very weak mechanical properties, but it was very apparent ... -
Mechanical design of latching/release mechanism
(Master thesis, 2022)This thesis documents the early development phase of a latch and release mechanism, where the goal was to make a 10mm separation within 10ms to break 4 electrical circuits. The thesis was proposed by Easee AS, a leading ... -
Mechanical performance of concrete made of steel fibers from tire waste
(Peer reviewed; Journal article, 2019)Currently, the disposal of used tires is a worldwide challenge, due to their non-degradability. Therefore, recycling has become a potential solution for managing such waste. During recycling, materials such as rubber and ... -
Mechanical Performance of Polymeric ARGF-Based Fly Ash-Concrete Composites: A Study for Eco-Friendly Circular Economy Application
(Peer reviewed; Journal article, 2022)At present, low tensile mechanical properties and a high carbon footprint are considered the chief drawbacks of plain cement concrete (PCC). At the same time, the combination of supplementary cementitious material (SCM) ... -
Mechanical properties and microstructure of 17-4 Ph stainless steel made by Jet binder additive manufacturing
(Bachelor thesis, 2023)Additive manufacturing is a field seeing constant innovation. This thesis looks at the mechanical properties and microstructure of a Binder Jet Printing (BJP) technology using the stainless steel alloy 17-4 PH. 17-4 PH is ...