Blar i Department of Mechanical and Structural Engineering and Materials Science (TN-IMBM) på tittel
Viser treff 1605-1624 av 1691
-
Use of simulator training to mitigate risks in arctic shipping operations
(Peer reviewed; Journal article, 2019)Over the recent years, ship traffic in the polar areas has increased. There is reason to believe that this traffic, and especially the cruise traffic, will increase further as the ice retracts towards the poles. There is ... -
Use of statistical methods and imperfection databank to determine the buckling strength for imperfect cylinders
(Master thesis, 2022)Buckling for thin metal shells are not an easy failure mode to design structures for. The large variety of geometries, material properties, and uncertainties has med standards and best practice for designing thin metal ... -
Use of submarines as field development facilities
(Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06)Today, it becomes clearer that the era of easy to extract oil is almost gone. Thus, the oil and gas industry starts to face the development of complex deposits located in deep and ultra-deep waters or in the Arctic region, ... -
Use risk-based method to develop a foundation for quantitatively assessing the contribution of maintenance activities in offshore petroleum oil and gas industry
(Masteroppgave/UIS-TN-IKM/2009, Master thesis, 2009)As the world market becomes more benefit-oriented, increasingly companies and organizations are becoming aware of the maintenance’s contribution to value generation, as well as its contribution to risk reduction. Maintenance ... -
Using digital technologies to automat and optimize drilling parameters in real-time, its impact on value creation, and work process
(Master thesis, 2023)The industry down-time from the second half of 2013 and corona pandemic has effectively turned most companies into introduction of new technologies and digitalization. The industrial landscape is undergoing innovation, ... -
Using Lifecycle Analysis (LCA) Towards Environmental and Human Health Footprints of Electrically Assisted Velomobile, PODBIKE
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-06-15)The transportation sector is responsible for the second largest ratio of the greenhouse gas emissions that can cause severe effects on human health and the environment. On the other hand, this sector is important by providing ... -
Using numerical analysis tools to increase the reliability of ultrasonic none intrusive inspection results for in-service pipeline flanges
(Masteroppgave/UIS-TN-IKM/2014;, Master thesis, 2014-06-15)This paper explores the benefits of simulating ultrasonic inspections on complex components with varying degradation scenarios. Ultrasonic inspection results on complex components are complex and difficult to decipher. ... -
Using the Kriging Response Surface Method for the Estimation of Failure Values of Carbon-Fibre-Epoxy Subsea Composite Flowlines under the Influence of Stochastic Processes
(Peer reviewed; Journal article, 2022)This paper investigates the use of the Kriging response surface method to estimate failure values in carbon-fibre-epoxy composite flow-lines under the influence of stochastic processes. A case study of a 125 mm flow-line ... -
Utbyttbar Skibinding
(Bachelor thesis, 2023)Et oppsett for alpintski kan variere veldig basert på hvilken type skikjøring som skal gjøres og hvordan forholdene er i bakken. Hovedsakelig er det utformingen på skien som bør endres basert på om det er mye løs snø, skare ... -
Utfelling av kromnitrider i bøyde duplexrør
(Bachelor thesis, 2021)Hensikten med denne oppgaven er å se om kompresjon har effekt på utfelling av kromnitrider i varmebehandlet, og bråkjølt, duplexstål av grad UNS S31803 og UNS S32205, med fellesbetegnelsen Duplex 2205. Duplex sin ... -
Utfelling av kromnitrider i bøyde duplexrør
(Bachelor thesis, 2021)Hensikten med denne oppgaven er å se om kompresjon har effekt på utfelling av kromnitrider i varmebehandlet, og bråkjølt, duplexstål av grad UNS S31803 og UNS S32205, med fellesbetegnelsen Duplex 2205. Duplex sin ... -
Utforske mulighetene for bruken av magnetiske roboter til overflatebehandling under tankvedlikehold
(Bachelor thesis, 2023)Denne bacheloroppgaven undersøker potensialet til magnetiske roboter for overflatebehandling under tankvedlikehold, og tar opp historiske utfordringer knyttet til oppgaven, som sikkerhetsrisikoer, støyeksponering og ... -
Utilization of Industrial By-Products/Waste to Manufacture Geopolymer Cement/Concrete
(Peer reviewed; Journal article, 2021-01)There has been a significant movement in the past decades to develop alternative sustainable building material such as geopolymer cement/concrete to control CO2 emission. Industrial waste contains pozzolanic minerals that ... -
Utilization of Polymer Concrete Composites for a Circular Economy: A Comparative Review for Assessment of Recycling and Waste Utilization
(Peer reviewed; Journal article, 2021-06)Polymer composites have been identified as the most innovative and selective materials known in the 21st century. Presently, polymer concrete composites (PCC) made from industrial or agricultural waste are becoming more ... -
Utilization of self-consolidated green material for sustainable development: An environment friendly waste materials application for circular economy
(Peer reviewed; Journal article, 2021-09)Self-Compacting Concrete (SCC) is a unique kind of concrete that tends to consolidate in terms of its weight. In this study, the prime target is to investigate the durability properties of SCC developed using eco-friendly ... -
Utilization of synthetic diamonds for cutting purposes in explosive atmospheres
(Masteroppgave/UIS-TN-IKM/2011;, Master thesis, 2011)Modifications in the process industry are quite common. For many of these modifications cutting of existing equipment and structure will be a central activity. The abrasive diamond wire cutting technology is adopted from ... -
Utilizing multiple criteria decision-making optimization methods to machine LM25Al/VC material under electro-discharge machining processes
(Peer reviewed; Journal article, 2023)In this work, sparking electro-discharge machining (EDM) process parameters are optimized by using multiple criteria decision-making (MCDM) methods. The work piece utilized for the investigation was LM25 aluminum alloy ... -
Utmattingsberegning for vindturbinfundament på løsmasser
(Masteroppgave/UIS-TN-IKM/2012;, Master thesis, 2012)Denne oppgaven omhandler en sammenligning av utmattingsberegninger for vindturbinfundament ut fra standardene DNV-OS-C502 og NS-EN 1992-1-1:2004. Oppgaven baseres på vindturbinene i Høg-Jæren Energipark. Før selve ... -
Utsira Nord Floating Wind farm – Optimalisation of marine operations related to inter-array cable installation.
(Master thesis, 2023)The offshore wind industry is experiencing significant growth, with wind farms expanding in size, capacity, and moving to more challenging locations. However, cable faults remain a major concern, particularly during the ... -
Utvikling av en teinehaler med kraftblokk for manuell drift
(Bachelor thesis, 2022)I denne oppgaven har man utviklet en teinehaler med manuell drift for hobbyfiskere med inspirasjon fra Northlift LH-300[1]. For å kartlegge behov i markedet ble det valgt å bruke markedsundersøkelse. Gjennom produktutvik ...