• Dynamic analysis of a suspension bridge 

      Tveiten, Jan (Masteroppgave/UIS-TN-IKM/2012;, Master thesis, 2012)
      This master thesis is the final part of my Master degree in structural and material science at the University of Stavanger. The thesis consists of collecting and studying data for the Lysefjord Bridge in light of the ...
    • Dynamic Analysis of a Vessel-shaped Fish Farm for Open Sea 

      Høiland, Andreas Vangdal (Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06-15)
      In recent years, aquaculture has been the fastest-growing animal food producing industry in the world. However, the absence of suitable production areas might potentially become the most limiting factor for future production ...
    • Dynamic analysis of damping system in FS car using ADAMS Multidynamic Simulations 

      Svendsen, Nick (Masteroppgave/UIS-TN-IKM/2014;, Master thesis, 2014-06-16)
      The aim of this thesis is to use manual calculations, ADAMS/Car and other CAE software to analyze the dynamic of the suspension system for Formula Student car. Manual calculations have been done to find the suitable ...
    • Dynamic analysis of emergency disconnect during workover operations 

      Kleppa, Sveinung (Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)
      Emergency disconnect from the stack-up with large rig offset during well intervention is considered as a critical operation. Failure of disconnection from the well can lead to a major accident. Unofficial figures suggest ...
    • Dynamic Analysis of Feed Pipes for Fish Farming in Open Sea 

      Gjuka, Asdren (Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06-15)
      The demand for seafood is continuously growing throughout the world, while the number of sheltered locations for fish farming is decreasing. Consequently, the industry is pushed to fin nd new and innovative solutions to ...
    • Dynamic analysis of flexible gravity-based fish cages under accidental failures in the mooring system 

      Dewan, Pulkit (Masteroppgave/UIS-TN-IMBM/2019;, Master thesis, 2019-06-15)
      A growing population needs an increasing amount of high-protein and nutritious food. Having acknowledged that, there is a substantial increase in seafood production in the world today. Due to spatial and environmental ...
    • Dynamic Analysis of Floating Dock Operations with Corrosion-induced Holes at Ballast Tanks 

      ZAHI, TERRY (Master thesis, 2023)
      The corrosion at the ballast tanks is a concern risk for floating docks that have been in service for several decades. Corrosion events can result in severe accidents and huge economic costs. To migrate the corrosion risk, ...
    • Dynamic analysis of gravity based fish cage 

      Chang, Ying (Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-07-06)
      With the development of economy and growth of population, we are constantly facing the challenge of decreasing fish population and increasing needs in the fish market. Aquaculture is a practical way to fulfill this demand. ...
    • Dynamic analysis of lift-off operation of a subsea spool from a barge 

      Karatas, Ismail Gokay (Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-07-15)
      The lift-off operation faces great operational challenges due to the harsh environment in the North Sea. Especially, the operation becomes more susceptible to environmental conditions when the installation method involves ...
    • Dynamic and Fatigue Analyses of Suspended Power Cables for Multiple Floating Offshore Wind Turbines 

      Beier, Dennis (Master thesis, 2023)
      Floating offshore wind turbines (FOWTs) are installed to effectively capture energy from offshore wind in deeper water areas where building bottom-fixed offshore wind turbines is not practical. The present study focuses ...
    • Dynamic loads on telescopic safety joint for workover riser 

      Fredrik Haugland, Danielsen (Masteroppgave/UIS-TN-IKM/2014;, Master thesis, 2014-06-05)
      The push in the industry towards increasing the weather window for marine operations offshore leads to a focus on new technology. When performing workover operations in a subsea well, the workover riser is a physical ...
    • Dynamic response of a floating bridge under wind conditions from field measurements 

      Syper, Joanna; Zhao, Ran (Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-06-28)
      The long and slender floating structures across the wide and deep waters are exposed for considerable environmental loads. In this study, the dynamic response of a curved floating pontoon bridge supported by side mooring ...
    • Dynamic response of a floating offshore wind turbine 

      Stølsmark, Rasmus (Masteroppgave/UIS-TN-IKM/2010;, Master thesis, 2010)
      The ever increasing demand for renewable energy, combined with limited areas suitable for large wind farms, has put focus on the development of floating wind turbines. In this thesis the dynamic response of a floating ...
    • Dynamisk analyse av bruer med jordskjelvlast 

      Kabeya, Jean Nounou (Masteroppgave/UIS-TN-IKM/2011;, Master thesis, 2011)
      Dette arbeidet ble utført våren 2011, som avslutning på studien Mastergrad i Konstruksjon og Materialer, ved Universitet i Stavanger, Norge. Oppgaven var meget utfordrende, først og fremst på grunn av omfanget (se 0.2 ...
    • E39 and Slipforming of environmental-friendly concrete 

      Kahsai, Bereket (Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020-06-15)
      Slipforming is a construction method that has been used in many years for production of concrete structures and it is mainly suited for tall structures such as towers, bridge columns, silos, and offshore platforms with ...
    • Eastern-Mediterranean Metocean Design Basis 

      Zughayar, Rami (Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-12-23)
      Energy is one of the basic requirements of sustainable development of civilizations. Mankind is moving further to harsher environments, e.g. marine and arctic environments, to sustain energy production. Technology evolution ...
    • EBSD and TEM study of DMD manufactured cp-TI (grade 2) 

      Berg, Alexander (Masteroppgave/UIS-TN-IMBM/2018;, Master thesis, 2018-06-29)
      Two components, 3D printed by Norsk Titanium components, through a direct metal deposition plasma transferred arc. An additive layer manufacturing technique. One made of a single wire layer thin sample, and one made of two ...
    • Eco-friendly and cost-effective slab for an office building 

      Laxsha Thurupan (Bachelor thesis, 2022)
      It is very popular to use prefabricated concrete elements instead of cast-in-situ slabs in many different construction buildings. The background of this thesis is to study how this apply to large construction buildings as ...
    • Effect of 3D printing on the microstructure and mechanical properties of an Inconel 718 Nickel-alloy (UNS N07718) 

      Petersen-Øverleir, Eivind (Masteroppgave/UIS-TN-IKM/2015;, Master thesis, 2015-06-15)
      Flow measuring instruments are important for the oil and gas industry. These instruments are exposed to hostile environments during operation. These hostile environments demands high quality materials with excellent ...
    • Effect of basalt minibars and steel fibers on the mechanical behavior of concrete. 

      Nikolov, Nikolay; Sultani, Omed (Bachelor thesis, 2021)
      Bruken av stålarmering i form av armeringsjern har vært brukt i mange år for å forbedre strekk- og bøyestyrken til betongelementer. Forskningen og utviklingen innen betongfeltet utvides stadig på grunn av at betong er det ...