Blar i Studentoppgaver (TN-IKM / TN-IMBM) på tittel
Viser treff 860-879 av 1213
-
Optimization of Multirotor UAV Endurance
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2020)Advancements in the technology of electric motors, batteries and control modules have facilitated a steep increase in the interest of small battery-powered multirotor aircraft. Unmanned areal vehicles (UAV) of this type ... -
Optimization of periodic maintenance using condition monitoring techniques and operational data
(Masteroppgave/UIS-TN-IKM/2012;, Master thesis, 2012)This thesis contributes optimization of periodic maintenance using condition monitoring techniques and operational data so that maintenance can be performed before critical equipment fails. Periodic maintenance is carried ... -
Optimization of Spar-Buoy Foundation for Offshore Wind Turbines Using Open-Source Programs
(Master thesis, 2021)Low carbon and renewable energy are paramount to tackle climate change and supply the increasing energy demand in a sustainable way. In recent years, the offshore wind industry has attracted growing attention for its ... -
Optimization of the Local Failure Design of Carbon-Fibre Epoxy Composite Curved Plates
(Masteroppgave/UIS-TN-IMBM/2020;, Master thesis, 2021-01-15)This thesis presents the optimization of the local failure design of Carbon-Fiber Epoxy Composite used in the manufacturing of the curved plates. As relatively new and reliable material carbon fiber can be used in different ... -
Optimization of the upper completion assembly by using redundant pump exemplified by the well in the Prirazlomnoye field, Pechora Sea
(Masteroppgave/UIS-TN-IKM/2017;, Master thesis, 2017-06)Nowadays development of Russian offshore oil and gas fields is relevant and perspective. A lot of Russian and foreign oil and gas companies tend to get an experience in offshore field development by establishing pilot ... -
Optimization of wiresheave
(Masteroppgave/UIS-TN-IKM/2014;, Master thesis, 2014-06-06)The objective of this thesis is to optimize a 72” (1828,8 mm) wire sheave with respect to weight and rotational inertia. The sheaves are used as pulleys on derrick structures. Seven different design concepts were designed ... -
Optimizing of Rack and Pinion System for Valve Intervention Tool
(Bachelor thesis, 2023)Hensikten med denne oppgaven er å se på forbedringer av rack- og pinion systemet som brukes i Izomax's isolasjonsverktøy Add On Gate Valve (AOGV). Dette systemet blir brukt til å sette inn en blindspade mellom to flenser ... -
Optimizing of Rack and Pinion System for Valve Intervention Tool
(Bachelor thesis, 2023)Hensikten med denne oppgaven er å se på forbedringer av rack- og pinion systemet som brukes i Izomax's isolasjonsverktøy Add On Gate Valve (AOGV). Dette systemet blir brukt til å sette inn en blindspade mellom to flenser ... -
Optimizing the installation process for future FOW developments in Europe, using Shoreline
(Master thesis, 2021)The increasing interest and demand for renewable energy in Europe have supported trials and developments of floating offshore wind turbines in deep waters. It is already well established that about 80% of Europe's potential ... -
Organizational Bottlenecks in New Technology Implementation and Utilization
(Masteroppgave/UIS-TN-IKM/2016;, Master thesis, 2016-06-15)The pace with which technology is currently developing is unparalleled in the history of mankind. Its development is continuously opening avenues through which tasks can be done in a more effective and efficient manner. ... -
Package Responsible Engineering
(Master thesis, 2022)Mechanical Packages Procedure According to NORSOK Requirement -
Parameter optimization in additive manufacturing (3D printing) for optimal mechanical and structural performance
(Master thesis, 2023)This master thesis explores the optimization of parameters in resin-based 3D printing to enhance mechanical and structural performance. The main problem was the development of residual stresses in the polymer resin during ... -
Parameter study of the effect of boulders on pipeline free span sections
(Masteroppgave/UIS-TN-IKM/2013;, Master thesis, 2013-06-17) -
Parametrisk analyse av fagverksbruer i tre: Optimalisert materialbruk med redusert karbonavtrykk
(Master thesis, 2021)Behovet for overgangsbruer i Norge øker i takt med at flere nye motorveier bygges. Norske overgangsbruer er i all hovedsak utført i betong, og kun et fåtall av dem er trebruer. Samtidig blir klimaet viktigere og flere ... -
Parametrization of Steel Lazy Wave Riser Configuration for Fatigue Considerations at the Touch Down Point
(Master thesis, 2022)With the advancement of technologies, deepwater oil and gas exploration has shown promising results worldwide. Production risers are integral in offshore hydrocarbon exploration because they transfer oil and gas from the ... -
Passive heave compensation of heavy modules
(Masteroppgave/UIS-TN-IKM/2008, Master thesis, 2008)New subsea technology has increased size and weight of installed modules significantly. This thesis looks at heavy module installation from barge, through moonpool with use of passive heave compensation. An installation ... -
Pålitelighetsutfordringer ved aldrende bruer
(Master thesis, 2014-06-16)Oppgaven her er delt inne i tre deler som er potensielle problemer for aldrende konstruksjoner. Disse er: - Kapasitets- og pålitelighets-analyse - Utmatting - Tilstandskontroll og tidsavhengige skademekanismer Det er ... -
Pendulum impact test of reinforced concrete structure
(Master thesis, 2021)Floating offshore concrete structures are vulnerable to collisions with ships, and the likelihood of accidents increase with increasing numbers of structures. Current design codes are not accurate for impact short duration ... -
Pendulum impact test of reinforced concrete structure
(Master thesis, 2021)Floating offshore concrete structures are vulnerable to collisions with ships, and the likelihood of accidents increase with increasing numbers of structures. Current design codes are not accurate for impact short duration ... -
Performance analysis of thrusters and using the concept of Design for Assembly for construction of an ROV-frame
(Bachelor thesis, 2021)This thesis aimed to develop an ROV-frame based on the concept of Design for Assembly, while conducting a performance analysis of the thrusters to be used for its required motion. The development of the ROV-frame and the ...